ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Gugor Kizuru
Country: Algeria
Language: English (Spanish)
Genre: Technology
Published (Last): 14 August 2018
Pages: 485
PDF File Size: 13.13 Mb
ePub File Size: 14.38 Mb
ISBN: 111-2-27412-571-9
Downloads: 34889
Price: Free* [*Free Regsitration Required]
Uploader: Zulubar

ASTM F594 Specification

The finished fasteners shall meet the applicable mechanical properties. Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. ashm

Free Technical Information

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make asfm representation that the contents of this abstract are accurate, complete or up to date.

AF asrm Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F E When approved by the purchaser, alloy F may be furnished.

TOP Related Posts  C3852A PDF

Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: F When approved by the purchaser, asgm or Se may be furnished.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall d594 of the same alloy group.

ASTM F – 09() Standard Specification for Stainless Steel Nuts

This abstract is a brief summary of the referenced standard. B legend of conditions: A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed.

A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

TOP Related Posts  CORIAN 810 SINK PDF

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including f54 and threading has been completed.

D Yield strength is the stress at which an offset of 0. A Tensile stress areas are computed using the following formula: Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. SH – Machined from strain hardened stock or cold worked to develop the specific properties.

Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties.

Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed. A Minimum values except where shown as maximum or as a range.